BMW R1100 Recalls

Item Affected: ELECTRICAL SYSTEM:WIRING
Date Announced: 1/5/1998

Description of Recall:
VEHICLE DESCRIPTION: MOTORCYCLES. A SHEET METAL PLATE MOUNTED TO THE FRONT OF THE FRAME BELOW THE INSTRUMENT CLUSTER CAN CAUSE THE WIRING HARNESS TO BE STRETCHED TOO TIGHT AS THE HANDLEBARS ARE TURNED FULLY TO ONE SIDE. IN ADDITION, THE WIRING HARNESS IS ATTACHED TO ANOTHER HARNESS WITH A CABLE TIE THAT IS PLACED TOO FAR FORWARD LIMITING THE HANDLEBAR MOVEMENT.

Action Needed To Fix It:
DEALERS WILL RELOCATE THE WIRE TIE CONNECTING THE TWO WIRING HARNESSES TO A POINT FURTHER BACK FROM THE ORIGINAL LOCATION SO THAT THE IGNITION SWITCH WIRING HARNESS HAS SUFFICIENT FREEDOM OF MOVEMENT. ALSO IF THE WIRING HARNESS IS FOUND TO BE DAMAGED, THE IGNITION SWITCH (WITH HARNESS) WILL BE REPLACED.

Find your local BMW Dealer.

Item Affected: ELECTRICAL SYSTEM:WIRING
Date Announced: 1/5/1998

Description of Recall:
VEHICLE DESCRIPTION: MOTORCYCLES. A SHEET METAL PLATE MOUNTED TO THE FRONT OF THE FRAME BELOW THE INSTRUMENT CLUSTER CAN CAUSE THE WIRING HARNESS TO BE STRETCHED TOO TIGHT AS THE HANDLEBARS ARE TURNED FULLY TO ONE SIDE. IN ADDITION, THE WIRING HARNESS IS ATTACHED TO ANOTHER HARNESS WITH A CABLE TIE THAT IS PLACED TOO FAR FORWARD LIMITING THE HANDLEBAR MOVEMENT.

Action Needed To Fix It:
DEALERS WILL RELOCATE THE WIRE TIE CONNECTING THE TWO WIRING HARNESSES TO A POINT FURTHER BACK FROM THE ORIGINAL LOCATION SO THAT THE IGNITION SWITCH WIRING HARNESS HAS SUFFICIENT FREEDOM OF MOVEMENT. ALSO IF THE WIRING HARNESS IS FOUND TO BE DAMAGED, THE IGNITION SWITCH (WITH HARNESS) WILL BE REPLACED.

Find your local BMW Dealer.

Item Affected: ELECTRICAL SYSTEM:WIRING
Date Announced: 1/5/1998

Description of Recall:
VEHICLE DESCRIPTION: MOTORCYCLES. A SHEET METAL PLATE MOUNTED TO THE FRONT OF THE FRAME BELOW THE INSTRUMENT CLUSTER CAN CAUSE THE WIRING HARNESS TO BE STRETCHED TOO TIGHT AS THE HANDLEBARS ARE TURNED FULLY TO ONE SIDE. IN ADDITION, THE WIRING HARNESS IS ATTACHED TO ANOTHER HARNESS WITH A CABLE TIE THAT IS PLACED TOO FAR FORWARD LIMITING THE HANDLEBAR MOVEMENT.

Action Needed To Fix It:
DEALERS WILL RELOCATE THE WIRE TIE CONNECTING THE TWO WIRING HARNESSES TO A POINT FURTHER BACK FROM THE ORIGINAL LOCATION SO THAT THE IGNITION SWITCH WIRING HARNESS HAS SUFFICIENT FREEDOM OF MOVEMENT. ALSO IF THE WIRING HARNESS IS FOUND TO BE DAMAGED, THE IGNITION SWITCH (WITH HARNESS) WILL BE REPLACED.

Find your local BMW Dealer.

Item Affected: ELECTRICAL SYSTEM:BATTERY:CABLES
Date Announced: 9/2/1993

Description of Recall:
THE POSITIVE BATTERY CABLE CONNECTOR MAY BE ATTACHED TO THE POSITIVE TERMINAL EXTENSION AT AN ANGLE WHICH MAY CAUSE CONTACT BETWEEN THE CONNECTOR AND THE BATTERY SUPPORT CAUSING AN ELECTRICAL SHORT.

Action Needed To Fix It:
REMOVE THE POSITIVE TERMINAL EXTENSION AND ATTACH THE POSITIVE BATTERY CABLE CONNECTOR DIRECTLY TO THE BATTERY TERMINAL WITH A BOLT.

Find your local BMW Dealer.

Item Affected: SUSPENSION:FRONT
Date Announced: 6/29/1994

Description of Recall:
CERTAIN SUSPENSION COMPONENTS CAN LOOSEN WHEN THE MOTORCYCLE IS RIDDEN HARD IN ROUGH OFF-ROAD CONDITIONS. THE RIGHT-HAND BEARING PIN IN THE REAR SWINGING ARM AND ALSO THE LOWER FLANGE NUT ON THE FRONT STRUT CAN BOTH LOOSEN.

Action Needed To Fix It:
DEALERS WILL REMOVE THE BEARING PIN, APPLY A STRONGER ADHESIVE AND REASSEMBLE WITH AN INCREASED TORQUE SPECIFICATION. THE FLANGE NUT ON THE FRONT STRUT WILL BE REPLACED WITH A SELF-TIGHTENING NUT.

Find your local BMW Dealer.